Drum Pump Motors

Water Treatment/Liquid Feed
Click Here to return to the Pumps page.

Electric Drum Pump Motors

SP-280P
OPEN DRIP PROOF
115V/1/60 -- 825 WATTS (1.11 hp)
220V/1/50 -- 825 WATTS (1.11 hp) CE

Thermally protected. Manual reset for safety. Drop in cartridge brush system. Yellow Valox housing for chemical resistance. 115V Models - 16 ft. (5m) of SJT3 wire cord with molded plug. 220V Models - IP-44 enclosure, CE listed, Har Ho7 cable, 5 M harmonized cord w/o plug.

Weight: 7.5 lbs. (3.4 kg)
NOT SUITABLE FOR FLAMMABLES.

SP-ENC
TEFC
115V/1/60 -- 825 WATTS (1.11 hp)
220V/1/50 -- 825 WATTS (1.11 hp) CE

Thermally protected. Manual reset for safety. Drop in cartridge brush system. Blue anodized housing for use in highly corrosive applications or where high levels of fumes are present. 115V models - 16 ft (5m) of SJT3 wire cord with molded plug. 220V models - IP-54 enclosure, CE listed, Har Ho7 cable, 5 M harmonized cord w/o plug.

Weight: 9.0 lbs. (4 kg.)
NOT SUITABLE FOR FLAMMABLES.

Pneumatic Drum Pump Motors

SP-A1
Maximum inlet pressure = 100psi (6.8 bar). Air consumption 22 CFM @ 92 psi (10.38 liter/sec @ 6.3 bar). Air connection 1/8î (3mm). Air line filter, pressure regulator and automatic oiler recommended. External muffler. NOTE: Flow rates are registered under a 1î (25.4mm) hose barb restriction.

Weight: 2.5 lbs. (1kg)
RPM: 7500

SP-A2
Maximum inlet pressure = 100psi (6.8 bar). Air consumption 28 CFM @ 90 psi (13.2 liter/sec. @ 6.2 bar). Air line filter, pressure regulator and automatic oiler recommended. External muffler. Plastisol coated handle for operator comfort and safety. NOTE: Flow rates are registered under a 1î (25.4mm) hose barb restriction.

Weight: 3 lbs. (1.3 kg)
RPM: 8000

NOTE: When pumping flammable liquids, the SP-A1 or SP-A2 air motor must be used in conjunction with an SP-SS pump end. Also, the Bond/Ground set should be utilized and all safety requirements should be met per OSHA and local safety requirements.

WARNING: Pumping of flammables or combustible liquids can generate a static electric discharge, causing fire or explosion resulting in injury or death. Read and understand operating instructions before starting this unit. Follow all federal, state and local safety codes including NFPA 30 -- NFPA77. Prior to connecting to air supply, install bond and ground wires and check continuity of each wire. A meter reading of one ohm or less is required for safe liquid transfer. Use only metallic drum, receiving vessel and metallic pump (SP-SS) when pumping flammables. Air motors are not recognized under any current Underwriter's Laboratory listing program. Consult a qualified engineer for suitability for use in a hazardous area or on flammables.

High Viscosity Pump End - SP700

The proper choice when pumping low to highly viscous oils, polymers and greases

FEATURES
Progressive cavity design. SS-316 construction with
stator materials available in BUNA-N, TFEÆ and VitonÆ.

Sizes:

27" (700mm) carboys
39" (1000mm) drums
43" (1100mm) tanks
47" (1200mm) tanks

Maximum Viscosity 100,000 SSU
Maximum Temperature 284ƒF (140ƒC)
Discharge 1.5" (38.1mm) hose barb
Tube Diameter 2" (51mm)
Shipping Weight 20 lb. (9kg) for all units

APPLICATIONS
Liquids with low or high viscosity, aggressive or neutral, with
or without fibers. Polymers, greases, oils, ink, shampoo, etc.

Motor Drives
SP-280P
  Open drip proof motor (IP-44)
SP-ENC
  TEFC motor (IP-54)
SP-400-2
  Explosion proof motor (Eex d II A T5) (220V/1/50-60Hz)
  Explosion proof motor (UL Group B,C,D) (120V/1/60Hz)
SP-A2
High volume air motor

Advantages of Modular Design


Modular Design allows quick and easy interchanging of all motors and pump ends. Highest Quality Shaft Material HastelloyÆ C-276 (PP, PVDF units) SS-316 (SS units) Finned TFEÆ Guide Sleeve is secured inside inner tube, ensuring stability and proper alignment. [A] Threaded Design maintenance is simplified w/o special tools allows quick replacement of rotor & pump housing ensures proper alignment of replacement components		[B] Easy-to-use Handwheel secures motor to pump end ensures proper coupling seatings safe handle for removal and transportation [C] Threaded Hose Coupling for safe and efficient hose removal. [D] Thick Wall Construction adds durability and prevents damage. [E] Pure Carbon 6038CÆ for the most chemically-resistant carbon bearing available.